FAQ Frequently Asked Questions

Our recipes are based on being prepared in an Omnia® Classic Original 2L. Omnia® Classic Maxi 3L is 50 percent larger. Therefore, in most recipes, you can increase the amount by half to double the batch. Start by increasing by half a batch only for recipes where the ingredients will rise in the pan during cooking. The cooking times are the same.

No, do not put water in the base. The bottom heat rises from the hot air.

Yes. If you use the Silicone Mold, it should always be generously greased and if you are using it to bake, flour it too.

Be careful with the heat, on a gas stove it’s easy to get too hot.

• On portable electric hot plate 2,000 W – use high heat.
• On an alcohol stove (like Origo/Cookmate) with an output of 2,000 W – a little less than half the output is usually fine.
• On a gas hob 2,500 W – start off testing just above the lowest flame.

Hint!

For short cooking times (10–20 minutes in total) and on an electric hot plate, the stainless steel base can be preheated on high heat for about 3 minutes. This facilitates the heating of the oven. Some bread and cakes need to be kick-started with a preheated base and oven at highest heat for 1 minute. Much like when you set a baking tray in a regular hot oven to get extra effect.

The best way to clean the Omnia® oven is to let it stand for a while with cold water in it. The cold water dissolves the starch in the food. Then wash with a little washing-up liquid in warm water as usual.

No! Aluminum should be washed by hand to avoid discoloration.

No, it is not dangerous. You can keep using your Omnia. The Pan will just be a little rougher and not as nice and smooth as before.

No, the Omnia®is made only in aluminium.

Yes, Omnia® Classic Original 2L and Omnia® Classic Maxi 3L.

No, induction only produces under heat. And not enough.

The stainless steel base is magnetic and therefore works on induction. But the shape of the bowl means that there is not enough heat. In addition, it doesn’t create any hot air that provides the heat from above. Do not use Omnia® Classic on induction.

Yes, the Omnia®works great on an electric burner, preferably 2000W.

Yes, you can.

Yes, the Omnia®works on a Trangia stove. Place the oven where you would normally use the frying pan. https://youtu.be/Y8RK9yPpkUo https://youtu.be/TI1BBFNylc8

Yes indeed. Omnia®can used on all sources of heat except induction hobs. The challenge can be to figure out the right heat for the Omnia.

Wash it with warm water and washing-up liquid. It is also dishwasher safe.

Try washing it with lemon water. Tips from customers: Preheat the oven at home to 175 °C/350 °F. Wash the silicone mold and place it in the oven for about 30 minutes.

No, not at all. Everything you can do with a silicone mold, you can also do directly in a well-greased and floured (when baking) Omnia® pan. The silicone mold primarily provides easier cleaning of the dish. The molds are especially appreciated by those who cook gratins and other food that normally sticks to the pan. When baking, the silicone mold makes it easier to pick up and tap out the bread or cake.

Damage to the Silicone Mold is usually caused by heat that is too high. Either the base was not used (it must always be used!) or the heat from the cooker was too high. If you are using an LPG cooker, it is especially important to be careful with the heat.

Omnia® Classic is a construction made up of three parts. The parts must always be used together and provide both heat from above and below. The Omnia® oven is a specially designed round shape with a hole in the middle. It stands on a bowl-shaped base that also has a hole in the middle. The bowl shape conducts warm air from the heat source along the underside of the Omnia® oven and provides heat from below. The center holes in the base and the Omnia® dish allows the heat from the stove to rise up through the construction, hit the lid and provide heat from above. The lid has ventilation holes.